How to Find the Fuse Box or Circuit Breaker Box

Co-authored by Jesse Kuhlman

Last Updated: November 13, 2023

While it is not a common occurrence, every once in a while you may have to replace a fuse or reset a breaker. It helps to know where your circuit breaker or fuse box is beforehand so you aren't searching in the dark during a power outage. Boxes can be anywhere from outside to in your basement. Once you've found it, it's important to know the difference between a circuit breaker box and a fuse box, and how to restore power.

Part 1

Part 1 of 3:

Finding Your Circuit Breaker or Fuse Box

Download Article

1
Search inside your home. Keep an eye out for a metal box, usually flush with the wall. The box will have a metal door to keep the breakers or fuses protected. Check your garage for the circuit breaker or fuse box. It might also be in a storage room, utility room, the basement, or a hallway.^{[1]
X
Expert Source

Jesse Kuhlman
Master Electrician, Kuhlman Electric

Expert Interview. 29 April 2020.}
- If you can't find your box in one of these areas, look again or see if you can spot where the power connects to your house from outside. Check for your box in the surrounding areas.
- If you live in an apartment, check in a cupboard or hallway.
2
Search outside if you can’t find it. Depending on how old your house is, your circuit breaker or fuse box could be outside.^{[2]
X
Expert Source

Jesse Kuhlman
Master Electrician, Kuhlman Electric

Expert Interview. 29 April 2020.} Start by checking next to the meter box for your house.
- If you have trouble finding your circuit breaker or fuse box, ask a neighbor where theirs is. If you live in a neighborhood with houses built in the same era, the boxes may be in similar locations.
- Call an electrician if you can't find your circuit breaker or fuse box. Some boxes can be hard to find depending on additions or remodeling done to the house.
Advertisement
3
Determine if you have a fuse box or a circuit breaker box. Once you've found your box, open the door. If you see rows of switches, you have a circuit breaker box. Fuses are round and screw into sockets in the fuse box, much like a light bulb.^{[3]
X
Research source}
- Older homes tend to have fuse boxes. If you have a particularly large house, you may even have multiple fuse or breaker boxes.^{[4]
  X
  Research source}

Part 2

Part 2 of 3:

Replacing a Blown Fuse

Download Article

1
Unplug any appliances in the same area where power loss occurred. If you lost power in your bedroom, unplug everything in that room before replacing any fuses.
- If you don't unplug any appliances before replacing the fuse, you run the risk of blowing the new fuse as well.
2
Turn off the main power in the fuse box. You should see a main power switch in the fuse box that can be toggled between On/Off. Wear gloves and rubber-soled shoes when working in the fuse box. Be sure to remove any jewelry before replacing fuses. It is possible to replace fuses without turning the main power off, but it is dangerous. Exercise caution when working in the fuse box.^{[5]
X
Research source}
- If there isn’t a switch to turn off the power, there will be a fuse block, usually in the center of the top row. Pull it out and check to see if it is labeled “on” and one side and “off” on the other. If so, reinsert it with the “off” side facing up. If not, leave it out while you replace the fuse, then reinsert it.
3
Find the broken fuse. In each fuse box, there should be a circuit list that tells you what fuses control what circuits. This will give you an idea of what fuse may have blown. Find the fuse that corresponds with the area of the house that lost power.^{[6]
X
Research source}
- The blown fuse will be cloudy or the metal line in the fuse will be broken.
- If you don't have a circuit list, you may have to guess which fuse is blown. If you pull a fuse out and no other circuits lose power, you've found the blown fuse.^{[7]
  X
  Research source}
4
Replace the fuse. To replace the fuse, simply screw the new fuse into the socket. Make sure you replace the fuse with a new one of the same amperage. Do not replace a blown fuse with one of a higher rating.^{[8]
X
Research source}
- Fuses are rated at 15, 20, or 30 amps. The higher the rating the larger the appliance they power.^{[9]
  X
  Research source}
- Typically if a fuse blows, it's because too many devices or appliances are pulling power from that circuit. If you're having a recurring problem with this, you may need to install a new circuit breaker to split the load.^{[10]
  X
  Expert Source
  
  Jesse Kuhlman
  Master Electrician, Kuhlman Electric
  
  Expert Interview. 29 April 2020.}
5
Turn on the main power. Once you have replaced the fuse, switch the main power back on. If you have a fuse block instead of a switch, replace the block with the side labeled “on” facing up. If the fuse blows again, call an electrician to inspect your wiring.
- If the fuse does not blow, plug in any appliances you were using. If the fuse blows, there could be a problem with the appliance. There could also be too many appliances plugged into one circuit.

Part 3

Part 3 of 3:

Resetting a Breaker

Download Article

When you trip a breaker and lose power to a room, unplug everything in that room.
2
Find the "tripped" breaker. You can spot the breaker in question by finding the switch that is out of line with the other switches. If you have power, your breakers should all be in the "on" position. The tripped breaker will either be flipped to "off" or it will not be fully on.
- Some circuit breakers have a red or orange mark on them that is easy to see when the switch is off. This can help you locate the tripped breaker.
3
Reset the breaker. Flip the tripped breaker all the way off before turning it back on. Many breakers will not reset unless they have been turned off completely.
- If the breaker trips immediately, call an electrician to inspect your wiring.
4
Test your power. Once you have flipped the breaker back on, plug your appliances back in. If you trip the breaker again, there may be an issue with your appliance, or you could be plugging too many appliances into one circuit.
- If you trip the breaker from plugging in too many appliances, try using a different outlet. If that does not solve the problem, call an electrician, as you may need to have a new circuit breaker installed.^{[11]
  X
  Expert Source
  
  Jesse Kuhlman
  Master Electrician, Kuhlman Electric
  
  Expert Interview. 29 April 2020.}

Expert Q&A

Search

Add New Question

Question

Where should I look to find my fuse box?

Jesse Kuhlman
Master Electrician, Kuhlman Electric
Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electric based in Massachusetts. Jesse specializes in all aspects of home and residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes.

Jesse Kuhlman

Master Electrician, Kuhlman Electric

Expert Answer

If you live in a home with a basement, the majority of the time it will be there. It might also be in the garage, a utility room, or on the outside of your home.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 2 Helpful 1

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Other names for a fuse box or breaker box include electrical box or service panel.

Thanks
Helpful 1 Not Helpful 0
Make sure all adults living in your home know where the fuse box or breaker box is located.

Thanks
Helpful 0 Not Helpful 0
If your box does not have a circuit list, you may need to create your own.

Thanks
Helpful 0 Not Helpful 0

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Never replace a blown fuse with one of a higher amperage. Doing so could start a fire.

Thanks
Helpful 10 Not Helpful 1
Do not block the path to your circuit breaker or fuse box. Leave 36 inches (91 cm) of clearance in front of the box and 30 inches (76 cm) on the sides. Make sure the box is 72 inches (180 cm) from the floor.

Thanks
Helpful 3 Not Helpful 0